Contattateci

JE-H(St)H...Bd FE180 E30-E90 B2ca

Wiring cable for industrial electronics, max. 225V, Keram
halogen-free, with improved fire characteristics,
with reference to VDE 0815,
circuit integrity (FE180) in accordance with VDE 0472-814, IEC 60331, EN 50200,
System Circuit Integrity E30-E90* in accordance with DIN 4102-12
Fire behaviour according to EN 50575, EN 13601-6

1 Conductor: solid
2 Insulation: cross-linked polymer, zero halogen
3 Drain wire: Ø 0.8 mm
4 Separator: plastic tape, zero halogen
5 Shielding: Al-laminated tape, zero halogen
6 Sheath: FRNC/LSZH

04_Propagation 06_Density 03_LS0H 05_Spread 07_Circuit 08_System CPR_B2ca CPR_Cca CPR_Dca CPR_Eca

Varianti di prodotto e stock

Articolo n. Stock ProdottoReaction to fireNumero di coreDiametro esterno della guaina [mm]Tasso di CU [kg/km]Weight [kg/km]Fire load [kWh/m]Unità di imballaggioGTIN / EAN
18809200BZ
JE-H(St)H...Bd FE180 E30-E90 1x2x0,8 mmB2ca-s1a,d1,a125.61540.30.108al metro40393910230260
18809200BK
JE-H(St)H...Bd FE180 E30-E90 1x2x0,8 mmB2ca-s1a,d1,a125.61540.30.1081000 m tamburo40393910474015
18809200BL
JE-H(St)H...Bd FE180 E30-E90 1x2x0,8 mmB2ca-s1a,d1,a125.61540.30.108500 m tamburo40393910474039
18809700BZ
JE-H(St)H...Bd FE180 E30-E90 2x2x0,8 mmB2ca-s1a,d1,a126.32558.80.138al metro40393910230284
18809700BL
JE-H(St)H...Bd FE180 E30-E90 2x2x0,8 mmB2ca-s1a,d1,a126.32558.80.138500 m tamburo40393910474152
18809700BK
JE-H(St)H...Bd FE180 E30-E90 2x2x0,8 mmB2ca-s1a,d1,a126.32558.80.1381000 m tamburo40393910474138
18809900BZ
JE-H(St)H...Bd FE180 E30-E90 4x2x0,8 mmB2ca-s1a,d1,a129.045100.50.224al metro40393910230307
18810200BZ
JE-H(St)H...Bd FE180 E30-E90 8x2x0,8 mmB2ca-s1a,d1,a1213.9852240.522al metro40393910230321
18810400BZ
JE-H(St)H...Bd FE180 E30-E90 12x2x0,8 mmB2ca-s1a,d1,a1214.8126285.40.605al metro40393910230345
18810600BZ
JE-H(St)H...Bd FE180 E30-E90 16x2x0,8 mmB2ca-s1a,d1,a1216.6166331.20.628al metro40393910230369
18810800BZ
JE-H(St)H...Bd FE180 E30-E90 20x2x0,8 mmB2ca-s1a,d1,a1218.8206428.60.842al metro40393910230383

Specifiche tecniche

Cables with intrinsic fire resistance are installed in all areas that require special protection of people and equipment against fire and fire damages and where strict security requirements must be fulfilled. Suitable for indoor applications. For outdoor applications, protection must be provided against exposure to direct sunlight. The cable should only be laid directly in earth or water if a protective conduit is used. These cables correspond to the demands of System Circuit Integrity E30-E90* in accordance with DIN 4102-12. System Circuit Integrity is guaranteed at an operating voltage up to 110V.
Permitted operating temperature at conductor of +70˚C.
Suitable according to VKF fire protection guideline in escape routes and in tunnels according to Astra guideline 13022.
operating capacity, 1km @ 800Hz 120
Test voltage 50Hz, core/core 500
peak voltage 225
Capacitive coupling 0,8 mm, 100m @ 800Hz 200
resistenza massima del loop 0,8 mm 73.2
Minimum insulation resistance 100
Test voltage 50Hz, core/screen 2000
Integrità del circuito FE 180
Integrità del circuito di sistema E90
Temperatura di installazione -5 °C - +50 °C
Temperatura di esercizio -30 °C - +70 °C
System Circuit Integrity is dependent on installation method.
Conduttore Bare copper, solid, 0.8 mm diameter, VDE 0815
Isolamento Fire-resistant, cross-linked, high-performance Keram special compound, EN 50290-2-36
Colori delle anime VDE 0815
Shielding Al-laminated tape with copper drain wire Ø 0.8 mm
Materiale della guaina esterna Flame retardant polyolefin compound VDE 0819-107, EN 50290-2-27 and VDE 0250-214 "HM 2"
Colore della guaina esterna arancia
Integrità del circuito IEC 60331-11/-21 (180 minutes), VDE 0472-814 (FE180), IEC 60331-1 (120 minutes), IEC 60331-2 (120 minutes), EN 50200 (PH120 minutes), NBN 713-020, VDE 0482-200 (PH120), AREI-RGIE Section 4.3.3 FR1
Integrità del circuito di sistema DIN 4102-12, AREI-RGIE Section 4.3.3 FR2
Reazione al fuoco EN 13501-6
Classe Euro B2ca
Densità dei fumi IEC 61034-1/-2, EN 61034-1/-2, VDE 0482-1034-1/-2, AREI-RGIE Section 4.3.3 SD
Senza alogeni, gas non corrosivi IEC 60754-1/-2, EN 60754-1/-2, VDE 0482-754-1/-2, AREI-RGIE Section 4.3.3 SA
Propagazione della fiamma AREI-RGIE Section 4.3.3 F1, EN 60332-1-2, IEC 60332-1-2, VDE 0482-332-1-2
Diffusione della fiamma IEC 60332-3-22/-24, EN 60332-3-22/-24, VDE 0482-332-3-22/-24, AREI-RGIE Section 4.3.3 F2
Curvatura minima durante l'installazione (multicore) 7.5 x D
Minimum bending radius permanent (multi core) 7.5 x D
Resistenza minima allo schiacciamento / 10cm 1000 N

Documentazione